Home > Gate Openers > Swing Gate Openers > Dual Swing Gate Opener > GG900 >

ETL Certified Dual Swing Gate Operator - GG900U/AS900U AC/DC - Basic Kit
ETL Certified Dual Swing Gate Operator - GG900U/AS900U AC/DC - Basic Kit - ALEKO


 
Alternative Views:
Price: CAD $809.97

Quantity in Stock:205


Availability:: Usually Ships in 24 to 48 Hours
Product Code: GG900UNOR-AC
Qty:

DETAILS
 

ALEKO ETL Certified GG900U/AS900U Dual Swing Gate Operator is designed for residential/commercial applications. Stay warm and dry in your vehicle. This Dual Swing Opener will handle dual swinging gates up to 20 ft in length and weighing up to 900 lb (10 ft and 450 lb per panel). ALEKO ETL GG900U/AS900U has powerful 24VDC motors, which provide exceptional starting torque and feature soft start/stop operation. This promotes longer gate and operator life, as well as dependable performance.

No power? No problem!

Optional Built-in battery backup provides seamless operation of the gate operator and all DC control and sensing devices in the event of a power loss. To simplify installation, ALEKO GG900U/AS900U Dual Swing Gate Operator may be installed with low-cost, low-voltage wiring or in remote locations using our optional 10W and/or 20W Solar Panel. Package includes: (2) actuators, (1) control box, (2) 8.5 x 11 inch warning signs, (2) release keys, (2) 433MHz remotes LM22, (1) set of accessories and mounting hardware for easy installation and (1) user manual with step by step installation instructions. Wire Sold Separately.
TECHNICAL SPECS:

  • Motor: 24V DC, 50W per actuator, 2A current
  • Power supply: 110V/60Hz (220V/50Hz - not included)
  • Actuator speed: 4.5 inches per second
  • Actuator travel: 15 inches
  • Max Weight of each gate panel: 450 pounds
  • Max Width of each gate panel: 10 feet
  • Auto-closing duration: programmable from 0-99 seconds
  • Ambient temperature: approximately -20C(-4F) ~ +50C(+122F)

FEATURES:

  • ALEKO ETL Certified Dual Swing Gate Operator
  • Access your gates through remote control or keypad
  • Smooth and soft start and stop function
  • Emergency Release key in case of power failure
  • Dual/Single gate running mode
  • Optional master and slave gate running
  • Adjustable opening/closing interval between master and slave gate
  • Stop/Reverse in case of obstruction during gate opening/closing
  • The force of the motor can be programmed
  • Optional photocell protection (not included)
  • Built in adjustable auto-close (programmable from 0-99 sec)
  • Digital display indicates the running situation and setting menu
  • Reliable electromagnetic limit switches improve adjustment of the 'open' and 'close' position

Average Rating: Average Rating: 4 of 5 4 of 5 Total Reviews: 1 Write a review »

  0 of 0 people found the following review helpful:
 
4 of 5 Aleko 900 Gate Opener Install Improvements May 16, 2023
Reviewer: Tom Wollschlaeger from Nanaimo, BC Canada  
Install manual Adjusting the Limit Switch not helpful.
My procedure for Dual Gate:
- use release key to disable actuator, stablize gate in desired close position
- detach actuator arm from gate, fully extend arm and tape measure
distance from arm end to magnetic ring in actuator cylinder ~1/2 inch in.
- reinstall actuator to gate, release key to reset, with previous measurement,
measure from arm end back to the actuator cylinder. Mark location in pencil
then unscrew Limit Switch B and position 'screw' at pencil mark.
- repeat on other actuator
- test gate open & close. If gap results on closure, note gap size in inches.
- IMPORTANT to reopen gate, then make adjustments, not when closed.
For every 1 inch, adjust Limit Switch by 1/8 inch or less. Logic says, if arm
is over extended, then move Limit Switch B closer in direction of Limit Switch A.
Else if under extended, move Limit Switch B away from Limit Switch A.
- Test gate & repeat only fine adjustments.

Was this review helpful to you?